ASTM D6484 PDF

ASTM D is a test method used to study the compressive properties of a composite laminate that has a hole cut into it. The GD fixture meets the requirements of ASTM D for open-hole compressive strength testing of fiber-reinforced polymer-matrix composite. The ASTM D / DM fixture is used to perform open-hole compressive tests on multi-directional polymer matrix composite laminates reinforced with high .

Author: Gakasa Magar
Country: Burkina Faso
Language: English (Spanish)
Genre: Software
Published (Last): 2 May 2010
Pages: 180
PDF File Size: 19.20 Mb
ePub File Size: 8.26 Mb
ISBN: 403-8-93039-844-6
Downloads: 86140
Price: Free* [*Free Regsitration Required]
Uploader: Fauzil

Combining values from the two systems may result in nonconformance with the standard. Each laboratory tested at ambient laboratory conditions a randomly distributed sample of six specimens for each loading type. If the ultimate strength of the material cannot be reasonably estimated, initial trials should be conducted using standard speeds until the ultimate strength of the material and the compliance of the system are known, and speed of testing can be adjusted.

The range of acceptable test laminates and thicknesses are described in 8. Valid OHC strength results should only be reported when appropriate failure modes are observed, in accordance with ASTM D Reference 5in the revision, added four holes in each end of the fixture for clamping bolts, as shown in Fig 4. Report the panel fabrication method. While the hole causes a stress concentration and reduced net section, it is common aerospace practice to develop notched design allowable strengths based on c6484 section stress to account for various stress concentrations fastener holes, free edges,?

Sources of variation in this lateral pressure include? The average results for each laboratory are listed in Table 2. This notation uses the? A detailed comparison qstm these fixtures is presented in Reference 8. Ultimate strength is calculated based on the gross crosssectional area, disregarding the presence of the hole. For typical specimen geometries, an instrument with an accuracy of 3?

ASTM D Open-Hole Compressive Strength of Polymer Matrix Composite Laminates_图文_百度文库

The force is transmitted by shear into the support? Astn of Additional Information: The fixture supports the test specimen continuously along both faces, a sufficient gap being designed into the staggered v-shaped joints in both sides of the fixture see the partially assembled fixture in Fig. Standard test specimens are 36 by mm [1. A number in parentheses indicates the year of last reapproval.

  COLONIALISMO Y NEOCOLONIALISMO SARTRE PDF

Take special care to ensure that creation of the specimen hole does not delaminate or otherwise damage d6844 material surrounding the hole.

The use of diamond tooling has been found to be extremely effective for many material systems. A NASA standard, described in Reference 6, specifies a much wider 5″ wide ashm and thus is not commonly used, being less conservative of the material being tested.

Reduce the compressive force to 7 N [30 lbf], and re-zero and balance all instrumentation. Ast, that influence the notched compressive strength and shall therefore be reported include the following: Precision and Bias Additionally, a micrometer or gage capable of determining the hole diameter to ?

ASTM D Open-Hole Compression (OHC) Testing of CFRP Video | LabTube

An optional threaded support plate is shown in Figs. The void content equations of Test Method D are applicable to both Test Method D and the matrix digestion procedures. Store the specimens in the conditioned environment until test time, if the test environment is different than the conditioning environment.

If you feel that your comments have not received c6484 fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.

NOTE 5—Other valuable data that can be useful in understanding testing anomalies and gripping or specimen slipping problems includes force versus strain data, percent edgewise bending, and force versus time data.

Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Shear loading is preferred in the Boeing specification, but requires relatively large hydraulic grips, i. Report the method of sampling. For non-ambient environmental conditions, the recommended? Some types of damage, such as longitudinal splitting and delamination, can blunt the stress concentration caused by the hole, increasing the force-carrying capacity of the coupon and the calculated strength.

  ECZEMA NUMULAR PDF

Report both the nominal where: The specimen, typically, but not necessarily, a quasi-isotropic laminate, is 12″ long, 1. Within the text the inch-pound units are shown in brackets. Two acceptable test procedures are provided. Historical Version s – view previous versions asm standard. Wyoming Test Fixtures Inc. The torque level may be increased above this level when acceptable failure modes cannot be achieved using 7 N-m [60 in-lbf] applied torque. Terminology E and Practice E de?

A gap outside of this tolerance range is indicative of either improper assembly, an out-of-tolerance specimen, or damaged? A cutout exists on both faces of the?

Two types of precision within-laboratory repeatability and between-laboratory reproducibility are reported. The composite material forms are limited to continuous-fiber or discontinuous-fiber tape or fabric, or both reinforced composites in which the laminate is balanced and symmetric with respect to the test direction. Link to Active This link will always route to the current Active version of the standard.

Combining values from the two systems may result in nonconformance with the standard.

ASTM D6484 Open-Hole Compression (OHC) Testing of CFRP

Performance of F-test and t-tests on the pooled data sets for each loading type indicated that both tests passed, such that the grip-loading and end-loading data sets were deemed compatible with qstm to mean behavior and variance. ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

Edgemounted extensometer displacement transducers are optional. It is the responsibility of the user of this standard to ast, appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Author: admin