2 1. ABOUT THE TRAINING SITE DESCRIPTION OF THE COMPANY ASELSAN A.Ş. As a developer of statü of the art Land, Air, Naval and Space. Aselsan Staj Aselsan Staj. November 14, | Author: hittaf_05 | Category: Drilling, Machining, Welding, Bending, Share Embed Donate. Report this link. of a company (like TUBITAK) or different departments of a company (like ASELSAN) is not . You report should start with a Cover Page and Table of . of the grades on the “Staj Değerlendirme Formu” must be at least 7.

Author: Salar Malakasa
Country: Costa Rica
Language: English (Spanish)
Genre: Literature
Published (Last): 12 January 2004
Pages: 393
PDF File Size: 16.62 Mb
ePub File Size: 10.43 Mb
ISBN: 823-1-75307-185-4
Downloads: 71002
Price: Free* [*Free Regsitration Required]
Uploader: Faunos

This process repeats until the current in the stator stops alternating or stops flowing.

By applying a voltage onto the primary of the transformer winding, a current flow results and induces current in the secondary winding. This type of encoder employs either contact brush or non-contact schemes of sensing position. The following will define each. With this device, there are several “techniques”, or design methodology, used to turn transistors “on” and “off”. Resonant conditions To explain this, imagine a yard stick held in your hand.

The induction motor operates much the same way that the synchronous motor does It uses the same magnetic principles to couple the stator and the rotor. Also the polarity aselszn the electro magnet can easily be reversed. Akakoca Kurtarma Kazs Ara Raporu. Higher voltage levels are needed to rotate the servo motor at appropriate higher speeds and higher current levels are required to provide torque to move heavier loads.


_aselsan staj

In addition, a zero index pulse can be provided to assist in determining the “home” position. The output signal may be square waves, or sinusoidal waves, or provide an absolute position. Slip is the difference between the stator magnetic field speed and the rotor speed.

If for some reason, either the signal or power does not get to the motor, or the motor is somehow prevented from rotating, the assumptions are poor and there would be no motion.

Internally, a “signal” winding rotor revolves inside a fixed stator.

Aselsan Staj

The output from the photosensor can be either a sine or square wave signal. We are a non-profit group that run this website to share documents. The rotor will try to follow the stator’s magnetic field, but will “slip” when a load is attached.

Systems that assume motion has taken place or is in the process of taking place are termed “open loop”. Staj Defteri, yaplan stajn gnlk raporlarn, rencinin staj yerini deerlendirme Documents. First of all, a look at the definition of these terms is in order and then how they affect performance.

Also I saw new repainig and soldering staff and used. Raooru secondary’s output signal would be a sine wave proportional to angle the other winding would be a cosine wavewith one electrical cycle of output voltage produced for each degrees of mechanical rotation.


This change is directly proportional to the angle which the rotor has been zselsan through. This technology achieves extremely high performance. High gain will allow small accurate movement and the machine will be capable of producing precise parts. Transistors act like a water faucet, regulating the appropriate amount of power to drive the motor. The ratio of the input signal as received from the radio station versus the output signal what your ear hears is gain.

Aselsan Staj Raporu – ingilizce

There are basically two aselsann of Stajj motors: This sequence occurs repeatedly, resulting in a jerky, cogging operation. This represents the output voltage generated from a tachometer when operated at rpm, i.

The number of tracks on the coded disk may be increased until the desired resolution or accuracy is achieved. Limits of the components they can handle only so much power.

An input signal loads a counter with positioning information. Gain, therefore is a measure of the amplification of the input signal. Rotor slots are filled with conductive material copper or aluminum and are short-circuited upon themselves by the conductive end pieces.

Author: admin