AKM 5381 PDF

ASAHI KASEI. [AKD].. / – 7 -. [ADC Plot: fs=48kHz]. AKM. AK THD+N vs. Input Level. VA=VD=V, fs=48kHz, fin=1kHz. AKM Semiconductor AKET. Explore Integrated Circuits (ICs) on Octopart: the fastest AKET. Dual Channel Dual ADC Delta-Sigma 96ksps bit. The AK achieves high accuracy and low cost by using Enhanced dual bit ∆Σ WARNING: AKM assumes no responsibility for the usage beyond the.

Author: Kigasar Nikorr
Country: Syria
Language: English (Spanish)
Genre: Photos
Published (Last): 22 November 2009
Pages: 86
PDF File Size: 13.63 Mb
ePub File Size: 9.86 Mb
ISBN: 612-2-61143-314-9
Downloads: 25526
Price: Free* [*Free Regsitration Required]
Uploader: Daigis

System analog ground and digital ground should be connected together near to where the supplies are brought onto the printed circuit board. VA and VD are usually supplied from the analog supply in the system. A critical component is one whose failure to function or perform may reasonably be expected to result, whether directly or indirectly, in the loss of the safety or effectiveness of the device or system containing it, and which must therefore meet very high standards of performance and reliability.

This reset should always be done after power-up. The input signal range scales a,m the supply voltage and nominally 0. Input voltage is proportional to VA voltage.

AKET IC DAC Audio Stereo 24bit Tssop16 Aket-e2 AKM UK Stock | eBay

Resolution 24 Bits Input Voltage Note 4 2. The cut-off frequency of the HPF is 1.

An analog initialization cycle starts after exiting the power-down mode. Operation at or beyond these limits may result in permanent damage to the device. Table 1 shows the relationship of typical sampling frequency and the system alm frequency. The AK requires no external components because the analog inputs are single-ended.


AKM 5381VT TSSOP16 100%

This value is the full scale 0dB of the input voltage. An evaluation board is available which demonstrates application circuits, the optimum layout, power supply arrangements and measurement results. Grounding and Power Supply Decoupling The AK requires careful attention to power supply and grounding arrangements.

All digital input pins should not be left floating. All voltages with respect to ground. All signals, especially clocks, should be kept away from the VCOM pin in order to avoid unwanted coupling into the AK The digital filter rejects noise above the stop band except for multiples of 64fs.

Date Code Marketing Code: AKM assumes no responsibility for the usage beyond the conditions in this datasheet. The ADC outputs settle wkm the data corresponding to the input signals after the end of initialization Settling approximately takes the group delay time. Normal operation is not guaranteed at these extremes.

The passband and stopband frequencies scale with fs. A hazard related device or system is one designed or intended for life support or maintenance of safety or for applications in medicine, aerospace, nuclear energy, or other fields, in which its failure to function or perform may reasonably be expected to result in loss of life or in significant injury or damage to person or property.

An electrolytic capacitor 2.

Профессиональные аудио-интерфейсы и их конвертеры (ЦАП/АЦП)

If these clocks are not provided, the AK may draw excess current due to its use of internal 581 refreshed logic. The calculated delay time induced by digital filtering.


The power up sequence between VA and VD is not critical. Decoupling capacitors should be as near to the AK qkm possible, with the small value ceramic capacitor being the nearest. The AK includes an anti-aliasing filter RC filter to attenuate a noise around 64fs.

This time is from the input of an analog signal to the setting of xkm data both channels to the ADC output register for ADC. Lead frame surface treatment: Alternatively if VA and VD are supplied separately, the power up sequence is not critical. No load current may be drawn from these pins.

The audio interface supports both master and slave modes. The AK samples the analog inputs at 64fs. AKM sales office or authorized distributor concerning their current status. In slave mode, the internal timing starts clocking by the rising edge 3581 edge at mode 1 of LRCK after exiting from reset and power down state by MCLK. In master mode, the internal timing starts when MCLK is input. Before considering any use or application, consult the Asahi Kasei Microsystems Co. Voltage Reference The voltage input to VA sets the analog input range.

The reference frequency of these responses is 1kHz.

Author: admin